1602液晶频率计的设计（Proteus仿真图和程序）.docx

《1602液晶频率计的设计（Proteus仿真图和程序）.docx》由会员分享，可在线阅读，更多相关《1602液晶频率计的设计（Proteus仿真图和程序）.docx（5页珍藏版）》请在优知文库上搜索。

1、基于51单片机的1602液晶频率计设计一、Proteus仿真图：二、程序代码最大测量65536Hz的频率计/原理：TO定时IS,Tl计数include#include#defineucharunsignedchar#defineuintunsignedintuintcount=0;uintnm=0;ucharFw,Fq,Fb,Fs,Fg;#defineDataPortPOsbitLCM.RS=P20;sbitLCM.RW=P2a1;sbitLCM.EN=P22;ucharcodestrO=-Testfrequency-)；ucharcodestrl=F=OOOOOHz);/ucharcodes

2、tr2=:voiddelay(unsignedintk)(unsignedintij;for(i=0;ik;i+)fr(j=0121+)(；)/=/*函数名：VoidWaiIFOrEnable(VOid)作用：检测忙碌信号*/=/voidWaitForEnable(Void)DataPort=Oxff;1.CM-RS=O;1.CM-RW=I;_nop_();1.CM_EN=1;.nopj);.nopj);While(DataPort&0x80);delay(5);1.CM-EN=O;)/=/*函数名：voidWriteCommandLCM(ucharCMD.ucharAtlribc)作用：写命

3、令到LCM*/=/voidWriteCommandLCM(ucharCMD,ucharAttribc)(if(Attribc)WaitForEnable();1.CM-RS=O;1.CM-RW=O;_nop_()；DataPort=CMD;-110P-();1.CM-EN=I;_nop_()；.nopj);1.CM-EN=O;/=/*函数名：VOidWriteDataLCM(uchardataW)作用：写数据*/=/voidWriteDataLCMCuchardataV)WaitForEnabIeO;1.CM-RS=I;1.CM-RW=O;.nopj);DataPort=dataW;-11op

4、-0;1.CM-EN=I;.nopj);-11op-();1.CM-EN=O;)/=/*函数名：voidInitLcdO作用：LCM初始化*/=/voidInitLcdOWriteCommandLCM(0x38,1);WriteComnandLCM(0x08,1);WriteCommandLCM(0x01,1);WriteComnandLCM(0x06,1);WriteCommandLCM(OxOc,1);/=/*函数名：voidDisplayOneChar(ucharX,ucharY,ucharDData)作用：显示指定坐标的一个字符*/=/voidDisplayOneCharCucharX

5、,ucharY,ucharDData)Y&=1;X=15;if(Y)X=0x40;X=0x80;WriteCommandLCM(X,0);WriteDataLCM(DData);/=/*函数名：voidDisplayListChar(ucharX,ucharY,ucharcode*DData作用：显示指定坐标的一串字符*/=/voidDisp1ayListChar(ucharX,ucharY,ucharcode*DData)ucharListLength=O;Y&=Oxl;X&=OxF;while(X=0;i)DiSPIayLiStChar(i,0,str);显示第一行字符DiSPlayLiSlChar(i,1,strl);显示第二行字符delay(100);1while(l)(if(nm=10)定时10*50MS=500ms(temp=TLl;tempI=THl;COUnI=2*(IemPI*256+iemp);定时2乘以500ms=100Omsdisplay();THl=计数器赋高8初值初值TLI=0;计数器赋低8初值nm=0;TRl=I;TRO=I;