QJYG10.01-8.1@机电工程材料验收标准2014.7.22.docx

《QJYG10.01-8.1@机电工程材料验收标准2014.7.22.docx》由会员分享，可在线阅读，更多相关《QJYG10.01-8.1@机电工程材料验收标准2014.7.22.docx（73页珍藏版）》请在优知文库上搜索。

1、江苏精亚机电工程有限公司机电工程材料验收标准Q/JYG10.01-8.1江苏精亚机电工程有限公司2014年7月第一部分通用类5第一章管材51.1 焊管、镀锌管51.2 无缝钢管6第二章型材72.1 角钢72.2 钢板82.3 槽钢10第二部分电气类12第一章主材121.1 镀锌扁钢121.2 PVC管121.3 桥架131.4 金属软管151.5 电线、电缆171.6 灯具211.7 配电箱221.8 母线槽221.9 开关、插座、接线盒231.10 灯座241.11 防火包24第二章辅材242.1 防水胶布242.2 电焊条252.3 黑胶布252.4 PVC胶粘剂262.5 铜线鼻子262

2、.6 压线帽27第三部分给排水29第一章主材291.1 AGR管291.2 柔性接口铸铁管291.3 灰铸铁管311.4 PP-R管321.5 给水衬塑复合钢管331.6 PVC-U管341.7 铜管351.8 薄壁不锈钢管361.9 PE给水管381.10 地漏411.11 法兰411.12 卫生陶瓷421.13 给水水箱441.14 水表451.15 臭氧消毒器461.16 水流指示器471.17 蝶阀471.18 截止阀481.19 减压阀491.20 浮球阀501.21 球阀511.22 闸阀52第二章辅材532.1 PVC-U管件532.2 灰口铸铁管件542.3 柔性铸铁管件55第

3、四部分采暖与通风空调56第一章主材561.1 PE-RT管561.2 PE-X管571.3 PB管581.4 玻璃钢风管601.6 波纹金属软管631.7 苯板641.8 挤塑板风管641.9 风口651.10 消声器661.11 散热器671.12 换热器681.13 冷却塔691.14 轴流风机691.15 直燃机组701.16 排烟防火阀711.17 调节阀721.18 通风蝶阀721.29 风机盘管73第一部分通用类第一章管材1.1 焊管、镀锌管一、 焊接钢管：执行国家GB/T13793-2001标准热镀锌管：执行国家GB/T3091-2001标准二、 产品应用于水、污水、燃气、空气、

4、采暖蒸气等低压流体输送和结构用的直缝焊接钢管。三、国标产品系列：长度：定尺6米/支焊管、镀锌管米重表表Ll型号mm公称口径/in规格mm(外径*壁厚)焊管国标米重Kg/m镀锌管国标米重Kg/m每件支数()DN154分21.3*2.751.261.34217支/件DN206分26.8*2.751.631.73169支/件DN251寸33.5*3.252.422.57127支/件DN32L2寸42.3*3.253.133.3291支/件DN40L5寸48*3.53.844.0791支/件DN502寸60*3.54.885.1761支/件DN652.5寸75.5*3.756.647.0437支/件D

5、N803寸88.5*4.08.348.8437支/件DNlO04寸114*4.010.8511.5019支/件DN1255寸140*4.515.0415.9419支/件DN1506寸165*4.517.8118.8819支/件DN2008寸219*6.031.5233.417支/件四、验收方法：1、外观检查：壁厚均匀，管口无毛刺，无锈蚀，弯折现象；整件包装完好；2、测量：用游标卡尺测量壁厚，用卷尺测量长度。用电子秤或磅秤测量重量。3、试验方法：电线管抽样检测DN1520,用弯管器现场煨弯，弯曲度和弯扁度符合要求；热镀锌管用锤适当敲外壁，观看是否有缝隙。4、资料要求：随车附带相应规格的产品质量证

6、明书。1.2 无缝钢管一、无缝钢管：执行国家GB17395-1998标准。二、型号与规格：无缝钢管型号与规格表1.2外径mm壁厚mm2.02.22.52.83.03.23.54.04.55.0理论重量kg/m502.372.592.933.253.483.704.014.545.055.55512.422.642.993.323.553.794.104.645.165.67532.522.763.113.463.703.944.274.835.385.92542.562.813.183.533.774.024.364.935.496.04562.662.923.303.663.924.174.

7、535.135.716.29572.712.973.363.744.004.254.625.235.836.41602.863.133.553.944.224.494.885.526.166.78633.013.303.724.154.444.735.135.816.497.14653.113.403.854.294.594.895.316.026.717.40683.263.574.044.494.815.125.576.317.057.77703.353.684.164.364.965.235.746.517.278.01733.503.844.354.845.185.526.006.81

8、7.608.38753.603.954.464.975.325.686.177.007.828.62763.654.004.535.055.405.756.267.107.938.75803.844.224.775.325.696.076.607.498.379.24834.004.374.965.525.926.316.867.798.719.62854.094.485.085.666.066.467.047.988.939.83894.294.705.335.946366.777.388.389.3810.33904.344.765.396.016.436.867.478.479.4910

9、.47954.595.025.706.366.817.267.908.9810.0411.101004.835.306.006.707.177.658.329.4610.5911.701024.935.406.136.847.327.818.509.6710.8211.961085.235.746.507.257.778.299.0210.2611.4912.701105.325.846.627.397.928.439.1910.4611.7012.931205.836.387.248.078.669.2210.0611.4412.9314.301256.066.647.548.429.029

10、.6110.5011.9113.3714.801307.868.789.4010.0010.9212.4313.9215.481338.058.989.5910.2511.1812.7514.2615.75140一一10.1110.7911.8013.4215.0516.65150一一一10.8511.5212.6514.3916.1117.85三、验收方法：1、外观检查：壁厚均匀，管口无毛刺，无锈蚀，弯折现象；整件包装完好；2、测量：用游标卡尺测量壁厚，用卷尺测量长度。用电子秤或磅秤测量重量。3、试验方法：抽样检测。4、资料要求：随车附带相应规格的产品质量证明书。第二章型材2.1 角钢一、角

11、钢：执行GB9787-88、GB9788-88标准。二、型号与规格：等边角钢的规格与尺寸(b边宽；d边厚；。内圆弧半径)表2.1角钢号数尺寸(mm)截面面积(cm2)理论重量(kgm)外表面积(m2m)bd22033.51.1320.8890.07841.4591.1450.0772.52531.4321.1240.09841.8591.4590.09733034.51.7491.3730.11742.2761.7860.1173.63632.1091.6560.14142.7562.1630.14153.3822.6540.141440352.3591.8520.15743.0862.4220.15753.7912.9760.1564.545352.6592.0880.17743.4862.7360.17754.2923.3690.17665.0763.9850.17655035.52.9712.3320.19743.8973.0590.19754.8033.7700.19665.6884.4650.1965.656363.3432.6240.22144.3903.4460.22055.4154.2510.22088.3676.5680.2196.363474.9783.9070.24856.1434.8220