砖砌体实测实量（样表）.docx

《砖砌体实测实量（样表）.docx》由会员分享，可在线阅读，更多相关《砖砌体实测实量（样表）.docx（3页珍藏版）》请在优知文库上搜索。

1、实测实量砖砌体结构工程记录表工程名称：南充深华工业集中区二期还房及公租房融资建设项目施工单位：中国五冶集团有限公司楼栋号/楼层：21#/8F测量:记录:日期:万部位门窗洞口尺寸偏差(mm)砌体垂直度(mm)砌体表面平整度(mm)断砖勾缝挂网(mm)备允许偏差设计实测允许偏差实测1实测2实测3允许偏差实测1实测2实测3(合格/不合格)合格值实测1图纸记号1-20,201000.0987.0-5,52.03.03.0-5,58.510.08.52图纸记号2-20,201000.0989.0-5,53.03.0-5,58.510.03图纸记号3-20,20900.0903.0-5,56.06.0-5

2、,514.015.04图纸记号4-20,20900.0895.0-5,54.07.0-5,56.55.05图纸记号5-20,201000.0980.0-5,54.04.0-5,57.09.06图纸记号6-20,201000.0994.0-5,511.011.0-5,56.57.57图纸记号7-20,201000.0971.0-5,54.07.0-5,53.03.58图纸记号8-20,201000.0903.0-5,53.03.0-5,57.04.09图纸记号9-20,20900.0904.0-5,54.03.0-5,54.03.510图纸记号10-20,20900.0907.0-5,57.04

3、.0-5,53.59.0评定合格数8147单项合格率=分项合格点数/总点数53.1%总点数98实测实量砖砌体结构工程记录表工程名称：南充深华工业集中区二期还房及公租房融资建设项目施工单位：中国五冶集团有限公司楼栋号/楼层：21#/8F专部位门窗洞口尺寸偏差（mm）砌体垂直度（mm）砌体表面平整度（mm）砖缝断勾挂网（mm）备允许偏差设计实测允许偏差实测1实测2实测3允许偏差实测1实测2实测3（合格/不合格）合格值实测11图纸记号11-20,20900.0912.0-5,52.06.05.0-5,55.08.53.512图纸记号12-20,20900.0901.0-5,57.03.0-5,53.

4、08.513图纸记号13-20,201100.01104.0-5,57.03.0-5,55.015.014图纸记号14-20,201100.01095.0-5,53.04.0-5,56.03.015图纸记号15-20,20-5,54.011.0-5,54.05.016图纸记号16-20,20-5,510.09.0-5,54.56.017图纸记号17-20,20-5,53.03.0-5,55.06.518图纸记号18-20,20-5,56.013.0-5,55.07.019图纸记号19-20,20-5,52.02.0-5,55.03.520图纸记号20-20,20-5,515.015.0-5,511.59.0评定合格数41112单项合格率=分项合格点数/总点数总点数46测量:记录:日期: